| After-sales Service: | Life Time |
|---|---|
| Warranty: | 12 Months Free |
| Delivery Time: | 15-30 Days |
| Application: | Battery Test |
| Standard: | Jisc 8714:2007, IEC62133-2017 |
| Net Weight: | 600kg |
| Customization: |
|---|
Suppliers with verified business licenses
Audited Supplier Standards: JISC 8714:2007, IEC62133-2017
This is a specialized equipment used to performing the forced internal short-circuit test under specific temperature and pressure, the battery is considered qualified if no explosion, no fire.
Specifications
| Temp. control box parameters | |
| Temp.range | 0ºC~100ºC |
| Temp. Resolution | ±0.1ºC |
| Temp. Fluctuation | ±0.5ºC |
| Temp. Uniformity | ±2ºC |
| Low temp. Limit | 0ºC |
| Temp. Rise rate | Average 3ºC/min(from 0ºC to 100ºC. |
| Temp. Drop rate | Average 1ºC/min(from 100ºC to 0ºC) |
| Internal cabinet material | 304SUS, base enhanced |
| Internal short-circuit test parameters | |
| Test load | 100kg( 1000N, normally 80kg);load resolution: 1/100,000 |
| Load resolution | 1/10,000;units:kg, lb, N |
| Load accuracy | ≤±1%F.S |
| Displacement resolution | ±0.01 mm |
| Speed range | 0.05~20mm/s adjustable,normal speed: 0.1mm/s |
| Effective range | 100mm(not include gripper) |
| Test max area | 200× 200mm(can be customized) |
| Voltage sampling range | 0~10V |
| Voltage resolution | 0.1‰F.S |
| Voltage sampling frequency | 100hz |
| Work platform material | SUS304 Stainless steel plate, with Teflon tape affixed to the surface of the test bench, high temperature and corrosion resistance, insulation |
| Press jig | Cylinder battery:10*10*15mm SUS+ 10*10*2mm Nitrile rubber |
| Square or prismatic battery:10*10*15mm SUS+ 10*10*2mm Nitrile rubber +5*5*2mm Acrylic |
|
| Press jig number | 5pcs each |
| Press mode | from top to bottom |
| Pressing procedure | At a speed of 0.1mm/s, apply pressure to the part where small nickel sheet is placed on the single battery, and at the same time use the voltage acquisition system to monitor the change of the battery output voltage (voltage acquisition frequency is 100 times/sec). When a voltage drop greater than 50mV is observed, or when the applied pressure meets the requirements (cylindrical battery 800N, square/ rhombic battery 500N/400N), stop pressing and hold for 30s, then release load |
| Control mode | PC remote control |
| Load measurement | Precision load cell measurement, computer display |
| Signal transmission | RS232 |
| Machine installation conditions | |
| Machine Net weight | 600kg |
| Machine dimensions | Host: W950× D900× H2000mm, Controller: W900× D600× H1300mm |
| Power supply | AC220V, 50Hz, 7.5kW |
| Temp. /humidity | No direct sunlight or other heat sources |
| Air\dust | Atmospheric pressure: 86~76kPa, Standard laboratory dust-free |
| Magnetic | No strong magnetic field and vibration around |
Standard configurations
5.1. Test machine host 1set
5.2. Control box 1set
5.3. Standard flat extrusion board 1 set
5.4. Standard extrusion head 5 each
5.5. Standard nickel sheet 5 pcs each
5.6. Test software 1 set
5.7. Test data cable 1pc
5.8. Computer 1 set
5.9. Instruction manual 1 copy
5.10. Product qualification certificate 1 copy
5.11. Product warranty card 1 copy
5.12. Packing list 1 copy
Suppliers with verified business licenses
Audited Supplier 
){kind=link}
){kind=link}